View LT1161_75319.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LT1161 Quad Protected High-Side MOSFET Driver
FEATURES
s s s s s s
DESCRIPTION
The LT1161 is a quad high-side gate driver allowing the use of low cost N-channel power MOSFETs for high-side switching applications. It has four independent switch channels, each containing a completely self-contained charge pump to fully enhance an N-channel MOSFET switch with no external components. Also included in each switch channel is a drain sense comparator that is used to sense switch current. When a preset current level is exceeded, the switch is turned off. The switch remains off for a period of time set by an external timing capacitor and then automatically attempts to restart. If the fault is still present, this cycle repeats until the fault is removed, thus protecting the MOSFET. The LT1161 has been specifically designed for harsh operating environments such as industrial, avionics, and automotive applications where poor supply regulation and/or transients may be present. The device will not sustain damage from supply voltages of -15V to 60V.
s s s s
Fully Enhances N-Channel MOSFET Switches 8V to 48V Power Supply Range Protected from - 15V to 60V Supply Transients Individual Short-Circuit Protection Individual Automatic Restart Timers Programmable Current Limit, Delay Time, and Auto-Restart Period Voltage-Limited Gate Drive Defaults to OFF State with Open Input Flowthrough Input to Output Pinout Available in 20-Lead DIP or SOL Package
APPLICATIONS
s s s s s
Industrial Control Avionics Systems Automotive Switches Stepper Motor and DC Motor Control Electronic Circuit Breaker
TYPICAL APPLICATION
24V CT 0.1F 0.1F 0.1F 0.1F RS 0.01 IRFZ34
+
V+ T1 T2 T3 T4 IN1 IN2 IN3 IN4 GND GND LT1161 V+ DS1 G1 DS2 G2 DS3 G3 DS4 G4
50F 50V
0.50 0.45 0.40
Switch Drop vs Load Current
TOTAL DROP (V)
0.01 IRFZ34 0.01 IRFZ34 0.01 IRFZ34
LOAD #1
0.35 0.30 0.25 0.20 0.15
LOAD #2
INPUTS
LOAD #3
0.10 0.05 0 0 1 3 2 LOAD CURRENT (A) 4 5
1161 TA01
LOAD #4
1161 F01
Figure 1. Protected Quad High-Side Switch
U
U
U
1
LT1161
ABSOLUTE MAXIMUM RATINGS
Supply Voltages (Pins 11, 20) ................... - 15V to 60V Input Voltages (Pins 3, 5, 7, 9) ...... (GND - 0.3V) to 15V Gate Voltages (Pins 12, 14, 16, 18) ........................ 75V Sense Voltages (Pins 13, 15, 17, 19).................. V + 5V Current (Any Pin).................................................. 50mA Operating Temperature Range LT1161C ............................................... 0C to 70C LT1161I ............................................ - 40C to 85C Junction Temperature Range (Note 1) LT1161C .............................................. 0C to 125C LT1161I ......................................... - 40C to 150C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C
PACKAGE/ORDER INFORMATION
TOP VIEW GND TIMER1 INPUT 1 TIMER 2 INPUT 2 TIMER 3 INPUT 3 TIMER 4 INPUT 4 1 2 3 4 5 6 7 8 9 20 V+
ORDER PART NUMBER LT1161CN LT1161CS LT1161IN LT1161IS
19 SENSE 1 18 GATE 1 17 SENSE 2 16 GATE 2 15 SENSE 3 14 GATE 3 13 SENSE 4 12 GATE 4 11 V + S PACKAGE 20-LEAD PLASTIC SOL
GND 10 N PACKAGE 20-LEAD PLASTIC DIP
JA = 70C/ W (N) JA = 110C/ W (S)
Consult factory for Military grade parts.
ELECTRICAL CHARACTERISTICS
SYMBOL IS IS(ON) VINH VINL IIN CIN VT(TH) VT(CL) IT VSEN ISEN VGATE - V + PARAMETER Supply Current Delta Supply Current (ON State) Input High Voltage Input Low Voltage Input Current Input Capacitance Timer Threshold Voltage Timer Clamp Voltage Timer Charge Current Drain Sense Threshold Voltage Temperature Coefficient Drain Sense Input Current Gate Voltage Above Supply
TA = 25C, V + = 12V to 48V each channel, unless otherwise noted.
MIN 3
q q
CONDITIONS All Channels OFF (Note 2) Measure Increase in IS per Channel
TYP 4.5 1
MAX 6.5 1.35 0.8 50 185 3.3 3.8 20 80 1.5 6 10 14 14 400 200 50
2 15 55 2.7 3.2 9 50 30 110 5 3 3.5 14 65 +0.33 0.5 4.5 8.5 12 12 220 75 25
VIN = 2V VIN = 5V VIN = 2V, Adjust V T VIN = 0.8V VIN = V T = 2V
q q q
tON tOFF tOFF(CL)
Turn-ON Time Turn-OFF Time Current Limit Turn-OFF Time
V + = 48V, VSEN = 65mV V + = 8V V + = 12V V + = 24V V + = 48V V + = 24V, VGATE > 32V, CGATE = 1000pF V + = 24V, VGATE < 2V, CGATE = 1000pF V + = 24V, (V + - VSENSE ) 0.1V, CGATE = 1000pF
q q q
4 7 10 10 100
UNITS mA mA V V A A pF V V A mV %/C A V V V V s s s
The q denotes specifications which apply over the full operating temperature range. Note 1: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formulas: LT1161CN, LT1161IN: TJ = TA + (PD x 70C/W) LT1161CS, LT1161IS: TJ = TA + (PD x 110C/W)
Note 2: Both V + pins (11, 20) must be connected together and both ground pins (1, 10) must be connected together.
2
U
W
U
U
WW
W
LT1161 TYPICAL PERFORMANCE CHARACTERISTICS
Supply Current
20 18 16 16 14 12 TJ = -40C TJ = 85C
GATE DRIVE CURRENT (A)
SUPPLY CURRENT (mA)
14 12 10 8 6 4 2 0 0 10 30 20 INPUT VOLTAGE (V) 40 50
1161 G01
VGATE - V +
ALL CHANNELS ON
ALL CHANNELS OFF
Supply Current
20 18 16 V + = 24V
INPUT THRESHOLD VOLTAGE (V)
DRAIN SENSE THRESHOLD VOLTAGE (mV)
SUPPLY CURRENT (mA)
14 12 10 8 6 4 2 0 -50 -25 25 50 0 TEMPERATURE (C) 75 100
1161 G04
ALL CHANNELS ON
ALL CHANNELS OFF
Turn-ON Time Driving MOSFET
500 450 400 IRFZ34
100 90 80 70 60 50 40 30 20 10
350 300 250 200 150 100 50 0 0 10 30 20 INPUT VOLTAGE (V) 40 50
1161 G07
RESTART PERIOD (ms)
TURN-OFF TIME (s)
TURN-ON TIME (s)
UW
MOSFET Gate Voltage Above V +
100
MOSFET Gate Drive Current
10 8 6 4 2 0 0
10
V + 24V V + = 12V V + = 8V
TJ = 25C
1
0.1
10 30 INPUT VOLTAGE (V) 20 40 50
1161 G02
0
2
6 10 12 14 4 8 GATE VOLTAGE ABOVE V + (V)
16
1161 G03
Input Threshold Voltage
2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -50 -25 25 50 0 TEMPERATURE (C) 75 100
1161 G05
Drain Sense Threshold Voltage
110 100 90 80 70 60 50 40 30 20 10 -50 -25 25 50 0 TEMPERATURE (C) 75 100
1161 G06
V + = 24V
V + = 24V
TURN-ON
TURN-OFF
Turn-OFF Time Driving MOSFET
1000
IRFZ34
Automatic Restart Period
V + = 24V CT = 3.3F
CT = 1F 100 CT = 0.33F
NORMAL
CURRENT LIMIT
CT = 0.1F 10 -50
0
0
10
30 20 INPUT VOLTAGE (V)
40
50
1161 G08
-25
0 25 50 TEMPERATURE (C)
75
100
1161 G09
3
LT1161
PIN FUNCTIONS
Supply Pins: The two supply pins are internally connected and must also be externally connected. In addition to providing the operating current for the LT1161, the supply pins also serve as the Kelvin connection for the current sense comparators. The supply pins must be connected to the positive side of the drain sense resistors for proper operation of the current sense. Input Pins: The input pins are active high and each pin activates a separate internal charge pump when switched ON. The input threshold is TTL/CMOS compatible but may be taken as high as 15V with or without the supply powered. Each input has approximately 200mV of hysteresis and an internal 75k pull-down resistor. Gate Pins: The gate pins drive the power MOSFET gates. When an input is ON, the corresponding gate pin is pumped approximately 12V above the supply. These pins have a relatively high impedance when above the rail (the equivalent of a few hundred kilohms). Care should be taken to minimize any loading by parasitic resistance to ground or supply. Sense Pins: Each sense pin connects to the input of a supply-referenced comparator with a 65mV nominal offset. When a sense pin is taken more than 65mV below supply, the MOSFET gate for that channel is driven low and the corresponding timing capacitor discharged. Each current-sense comparator operates completely independently. The 65mV typical threshold has a +0.33%/C temperature coefficient, which closely matches the TC of drain sense resistors formed from copper PC traces. Some loads require high in-rush currents. An RC time delay can be added between the drain sense resistor and the sense pin to ensure that the current-sense comparator does not false trigger during start-up (see Applications Information). However, a maximum of 10k can be inserted between a drain sense resistor and the sense pin. If current sense is not required in any channel, the sense pin for that channel is tied to supply. Timer Pins: A timing capacitor CT from each timer pin to ground sets the restart time following overcurrent detection. CT is rapidly discharged to less than 1V and then recharged by a 14A nominal current source back to the timer threshold, whereupon restart is attempted. If current sense is not required in any channel, the timer pin for that channel is left open. Ground Pins: The two ground pins are internally connected and must also be externally connected.
FUNCTIONAL DIAGRA
14A TIMER
3V
1.4V 75k INPUT 75k
4
W
U
U
U
U
U
(Each Channel)
V+
+ - + - + - + -
1.4V OSCILLATOR AND CHARGE PUMP
65mV
SENSE
GATE
1161 FD
LT1161
OPERATIO
The LT1161 gate pin has two states, OFF and ON. In the OFF state it is held low, while in the ON state it is pumped to 12V above supply by a self-contained 750kHz charge pump. The OFF state is activated when either the input pin is below 1.4V or the timer pin is below 3V. Conversely, for the ON state to be activated, both the input and timer pins must be above their thresholds. If left open, the input pin is held low by a 75k resistor, while the timer pin is held a diode drop above 3V by a 14A pullup current source. Thus the timer pin automatically reverts to the ON state, subject to the input also being high. The input has approximately 200mV of hysteresis. The sense pin normally connects to the drain of the power MOSFET, which returns through a low valued drain sense resistor to supply. When the gate is ON and the MOSFET drain current exceeds the level required to generate a 65mV drop across the drain sense resistor, the sense comparator activates a pull-down NPN which rapidly pulls the timer pin below 3V. This in turn causes the timer comparator to override the input pin and activate the gate pin OFF state, thus protecting the power MOSFET. In order for the sense comparator to accurately sense MOSFET drain current, the LT1161 supply pins must be connected directly to the positive side of the drain sense resistors.
APPLICATIONS INFORMATION
Input/Supply Sequencing There are no input/supply sequencing requirements for the LT1161. The input may be taken up to 15V with the supply at 0V. When the supply is turned on with an input high, the MOSFET turn-on will be inhibited until the timing capacitor charges to 3V (i.e., for one restart cycle). The two V + pins (11, 20) must always be connected to each other. Isolating the Inputs Operation in harsh environments may require isolation to prevent ground transients from damaging control logic. The LT1161 easily interfaces to low cost opto-isolators. The network shown in Figure 3 ensures that the input will be pulled above 2V, but not exceed the absolute maximum
LOGIC GND POWER GROUND
U
W
U
U
U
(Each Channel, Refer to Functional Diagram)
When the MOSFET gate voltage is less than 1.4V, the timer pin is released. The 14A current source then slowly charges the timing capacitor back to 3V where the charge pump again starts to drive the gate pin high. If a fault still exists, such as a short circuit, the sense comparator threshold will again be exceeded and the timer cycle will repeat until the fault is removed (see Figure 2).
OFF INPUT NORMAL OVERCURRENT NORMAL
12V V+ GATE 0V
3V TIMER 0V
1161 F02
Figure 2. Timing Diagram
rating, for supply voltages of 12V to 48V over the entire temperature range. In order to maintain the OFF state, the opto must have less than 20A of dark current (leakage) hot.
12V TO 48V 100k LOGIC INPUT 2k 1/4 NEC PS2501-4
IN 51k LT1161 GND GND
1161 F03
Figure 3. Isolating the Inputs
5
LT1161
APPLICATIONS INFORMATION
Drain Sense Configuration The LT1161 uses supply-referenced current sensing. One input of each channel's current-sense comparator is connected to a drain sense pin, while the second input is offset 65mV below the supply bus inside the device. For this reason, pins 11 and 20 of the LT1161 must be treated not only as supply pins, but as the reference inputs for the current-sense comparators. Figure 4 shows the proper drain sense configuration for the LT1161. Note that the sense pin goes to the drain end of the sense resistor, while the two V + pins are tied to each other and connected to supply at the same point as the positive ends of the sense resistors. Local supply decoupling at the LT1161 is important at high input voltages (see Protecting Against Supply Transients). The drain sense threshold voltage has a positive temperature coefficient, allowing PTC sense resistors to be used (see Printed Circuit Board Shunts). The selection of RS should be based on the minimum threshold voltage: 50mV RS = ISET Thus the 0.02 drain sense resistor in Figure 4 would yield a minimum trip current of 2.5A. This simple configuration is appropriate for resistive or inductive loads which do not generate large current transients at turn-on.
24V V+ V+ LT1161 DS1
1161 F04
+
10F
RS 0.02 (PTC) IRFZ34
T1 CT 1F
G1 GND GND
24V, 2A SOLENOID
Figure 4. Drain Sense Configuration
6
U
+
W
U
U
Automatic Restart Period The timing capacitor CT shown in Figure 4 determines the length of time the power MOSFET is held off following a current limit trip. Curves are given in the Typical Performance Characteristics to show the restart period for various values of CT. For example, CT = 0.33F yields a 50ms restart period. Defeating Automatic Restart Some applications are required to remain off after a fault occurs. When the LT1161 is being driven from CMOS logic, this can be easily implemented by connecting resistor R1 between the input and timer pins as shown in Figure 5. R1 supplies the sustaining current for an SCR which latches the timer pin low. This prevents the MOSFET gate from turning ON until the input has been recycled.
TIMER R1 2k 5V CMOS LOGIC ON = 5V OFF = 0V LT1161 INPUT
1161 F05
Figure 5. Latch-Off Input Network (Auto-Restart Defeated)
Inductive vs Capacitive Loads
100F 50V
Turning on an inductive load produces a relatively benign ramp in MOSFET current. However, when an inductive load is turned off, the current stored in the inductor needs somewhere to decay. A clamp diode connected directly across each inductive load normally serves this purpose. If a diode is not employed the LT1161 clamps the MOSFET gate 0.7V below ground. This causes the MOSFET to resume conduction during the current decay with (V + + VGS + 0.7V) across it, resulting in high dissipation peaks. Capacitive loads exhibit the opposite behavior. Any load that includes a decoupling capacitor will generate a current equal to CLOAD x (V/t) during capacitor in-rush. With large electrolytic capacitors, the resulting current
LT1161
APPLICATIONS INFORMATION
spike can play havoc with the power supply and false trip the current-sense comparator. Turn-on V/t is controlled by the addition of the simple network shown in Figure 6. This network takes advantage of the fact that the MOSFET acts as a source follower during turn-on. Thus the V/t on the source can be controlled by controlling the V/t on the gate: and CD delay the overcurrent trip for drain currents up to approximately 10 x ISET, above which the diode conducts and provides immediate turn-off (see Figure 7). To ensure proper operation of the timer, CD must be CT.
10
TRIP DELAY TIME (1 = RDCD)
V V + - VTH = t 105 x C1
where VTH is the MOSFET gate threshold voltage. Multiplying CLOAD times this V/t yields the value of the current spike. For example, if V + = 24V, VTH = 2V, and C1 = 0.1F, V/t = 2.2V/ms, resulting in a 2.2A turn-on spike into 1000F. The diode and second resistor in the network ensure fast current limit turn-off. When turning off a capacitive load, the source of the MOSFET can "hang up" if the load resistance does not discharge CLOAD as fast as the gate is being pulled down. If this is the case, a diode may have to be added from source to gate to prevent VGS(MAX) from being exceeded.
CURRENT LIMIT DELAY NETWORK V+ V+ DS LT1161 V/t CONTROL NETWORK 1N4148 100k G C1 100k 1RFZ24 1N4148 CD RD (10k) 24V
+
CLOAD
1161 F06
Figure 6. V/t Control and Current Limit Delay
Adding Current Limit Delay When capacitive loads are being switched or in very noisy environments, it is desirable to add delay in the drain current-sense path to prevent false tripping (inductive loads normally do not need delay). This is accomplished by the current limit delay network shown in Figure 6. RD
U
W
U
U
1
0.1
0.01 10 100 1 MOSFET DRAIN CURRENT (1 = SET CURRENT)
L1161 F07
Figure 7. Current Limit Delay Time
Printed Circuit Board Shunts The sheet resistance of 1oz. copper clad is approximately 5 x 10 -4 /square with a temperature coefficient of +0.39%/C. Since the LT1161 drain sense threshold has a similar temperature coefficient (+0.33%/C), this offers the possibility of nearly zero TC current sensing using "free" drain sense resistors made out of PC trace material. A conservative approach is to use 0.02" of width for each 1A of current for 1oz. copper. Combining the LT1161 drain sense threshold with the 1oz. copper sheet resistance results in a simple expression for width and length: Width (1oz. Cu) = 0.02" x ISET Length (1oz. Cu) = 2" The width for 2oz. copper would be halved while the length would remain the same. Bends may be incorporated into the resistor to reduce space; each bend is equivalent to approximately 0.6 x width of straight length. Kelvin connections should be employed by running separate traces from the ends of the resistors back to the LT1161 V + and sense pins. See Application Note 53 for further information on printed circuit board shunts.
+
7
LT1161
APPLICATIONS INFORMATION
Low Voltage/Wide Supply Range Operation When the supply is <12V, the LT1161 charge pumps do not produce sufficient gate voltage to fully enhance standard N-channel MOSFETs. For these applications, logiclevel MOSFETs can be used to extend operation down to 8V. If the MOSFET has a maximum VGS rating of 15V or greater, then it can also be used up to the 60V (absolute maximum) rating of the LT1161. MOSFETs are available from both Motorola and Siliconix which meet these criteria. Protecting Against Supply Transients The LT1161 is 100% tested and guaranteed to be safe from damage with 60V applied between the V + and ground pins. However, when this voltage is exceeded, even for a few microseconds, the result can be a catastrophic failure. For this reason it is imperative that the LT1161 not be exposed to supply transients above 60V. For proper current-sense operation, the pins are required to be connected to the positive side of the drain sense resistors (see Drain Sense Configuration). Therefore, the best way to prevent supply transients is to ensure that the supply is adequately decoupled at the point where the V + pins and drain sense resistors meet. Several hundred microfarads may be required with high current switches. When operating voltages approach the 60V absolute maximum rating of the LT1161, local supply decoupling between the V + pins (11, 20) and ground pins (1, 10) is highly recommended. A small ferrite bead between the supply connection and local capacitor can also be effective in suppressing transients. Note however, that resistance should not be added in series with the V + pins because it will cause an error in the current sense threshold. Fault Feedback Two methods can be used to derive switch status. First, the timer pin voltage can be monitored to indicate when the switch is turned off due to current limit. During normal operation (ON or OFF), the timer voltage is 3.5V and only during current limit does the voltage drop below 3V.
1F
V+
8
U
W
U
U
The second method shown in Figure 8 uses a quad exclusive-NOR gate to indicate when the output of the switch has not obeyed the input command (i.e., output low when it should be high or vice versa). In addition to current limit, this gives a fault indication if the switch is shorted or if the load is open.
24V V+ V+ DS ROL ADD FOR OPEN-LOAD DETECTION
+
RS
LT1161 INPUT FAULT 1/4 MM74HC266A 100k IN
G
LOAD
1161 F08
Figure 8. Fault Feedback Using Exclusive-NOR Gate
Low-Side Driving Although the LT1161 is primarily targeted at high-side (grounded load) switch applications, it can also be used for low-side (supply-connected load), or mixed high- and low-side switch applications. Figures 9a and 9b illustrate LT1161 switch channels driving low-side power MOSFETs. Because the LT1161 charge pump tries to pump the gate of the N-channel MOSFET above supply, a clamp zener is required to prevent the VGS (absolute maximum) of the MOSFET from being exceeded. The LT1161 gate drive is current limited for this purpose so that no resistance is needed between the gate pin and zener.
12V TO 48V V+ V+ T DS 4A LOAD G 15V 1N4744
1161 F09a
+
100F
RS 0.01 (PTC)
LT1161
IRFZ44
Figure 9a. Low-Side Driver with Load Current Sensing
LT1161
APPLICATIONS INFORMATION
8V TO 24V HV 1N4148 V+ T1 1F LT1161 V+ DS1 G1 2N2222 51 T2 1F DS2 G2 IRF630 15V 1N4744 RS1 0.2 51
+
10F
HV LOAD
IRF630
+
2N2222 51 1/2 LT1013
-
15V 1N4744
Figure 9b. Low-Side Drivers with Two Approaches for Source Current Sensing
Current sensing for protecting low-side drivers can be done in several different ways. In the Figure 9a circuit, the supply voltage for the load is assumed to be within the
TYPICAL APPLICATIONS
Using an Extra Channel to Do Common Current Limit for Multiple/Paralleled Switches
24V 100k 1F 2 1 20 19 18 17 16 15 14 13 12 IRFZ44
1161 TA05
GND T1 IN1 T2 IN2 T3 IN3 T4 IN4 GND LT1161
+
3 4 5 6
INPUTS (MAY BE PARALLELED)
7 8 9 10
U
W
U
U
U
HV LOAD
supply operating range of the LT1161. This allows the load to be returned to supply through current-sense resistor RS, providing normal operation of the LT1161 protection circuitry. If the load cannot be returned to supply through RS, or the load supply voltage is higher than the LT1161 supply, the current sense must be moved to the source of the low-side MOSFET. Figure 9b shows two approaches to source sensing. On channel 1, current limit occurs when the voltage across sense resistor RS1 thresholds the VBE of the NPN transistor, causing the LT1161 drain sense pin to be pulled down. The channel 2 circuit of Figure 9b uses an operational amplifier (must common mode to ground) to level shift the voltage across RS2 up to the drain sense pin. This approach allows the use of a much smaller sense resistor which could be made from PC trace material. In both cases, the LT1161 restart timers function the same as in high-side switch applications.
RS2 0.02
1161 F09b
V+ DS1 G1 DS2 G2 DS3 G3 DS4 G4
+ 10F
RS 15k 50V
IRFZ44
IRFZ44 OUTPUTS (MAY BE PARALLELED)
11 V+
9
LT1161
TYPICAL APPLICATIONS
Protected Quad 1A Automotive Solenoid Driver with Overvoltage Shutdown
0.33F 1N4148 0.33F 1N4148 0.33F 1N4148 0.33F 1N4148
INPUTS
Protected Quad Switch with Mixed Low- and High-Side Driving
10F 24V 0.01 1 2 3 HIGH-SIDE DRIVER INPUTS (SEE NOTE 1) 0.33F 4 5 2k 6 7 LOW-SIDE DRIVER INPUTS (SEE NOTE 2) 2k 8 9 10 GND T1 IN1 T2 IN2 T3 IN3 T4 IN4 GND LT1161 V+ DS1 G1 DS2 G2 DS3 G3 DS4 G4 V+ 20 19 18 17 16 15 14 13 2N2222 12 11 51 15V 1N4744 MTP10N40E 51 MTP10N40E 15V 1N4744 1N4148 0.4 150V/1A LOAD MTP36N06E 0.01 MTP36N06E 1N4148 24V/3A LOAD
+
0.33F
NOTE 1: THE HIGH-SIDE DRIVER CHANNELS ARE CONFIGURED TO AUTOMATICALLY RESTART FOLLOWING A FAULT. NOTE 2: THE LOW-SIDE DRIVER CHANNELS ARE CONFIGURED TO LATCH OFF FOLLOWING A FAULT. 5V CMOS LOGIC INPUTS ARE REQUIRED.
10
U
1 2 3 4 5 6 7 8 9 10
GND T1 IN1 T2 IN2 T3 IN3 T4 IN4 GND LT1161
20 V+ DS1 G1 DS2 G2 DS3 G3 DS4 G4 V+ 19 18 17 16 15 14 13 12 11
8V TO 28V OPERATING 32V TO 60V SHUTDOWN
0.03 MTD3055EL 0.03 MTD3055EL 0.03 MTD3055EL 0.03 MTD3055EL
+
10F 100V
2N3904 5.1k 10k 30V 1N6011B
1161 TA03
+
100F 50V 24V/3A LOAD 150V/1A LOAD 150V
2N2222
0.4
1161 TA04
LT1161
TYPICAL APPLICATIONS
Protected Quad 2A Industrial Switch with Isolated Inputs and Fault Output
5.1k
NEC PS2501-4 1F
5.1k 1F INPUTS 5.1k 1F
5.1k 1F
24V
18k 2N3904 5.6V 1N5994B 4N28 FAULT OUTPUT 5.1k 0.1F
1161 TA02
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
U
24V 1 GND T1 IN1 T2 IN2 T3 IN3 T4 IN4 GND LT1161 20 V+ DS1 G1 DS2 G2 DS3 G3 DS4 G4 V+ 19 18 17 16 15 14 13 12 11 0.015 RFD16N05 0.015 RFD16N05 0.015 100k RFD16N05 0.015 RFD16N05 100k LOAD #4 LOAD #3 100k LOAD #2 LOAD #1
+
+
2 3
50F 50V
+
4 5
+ +
6 7 8 9 10
MM74HC266A
100k
2k
11
LT1161
PACKAGE DESCRIPTION U
Dimension in inches (millimeters) unless otherwise noted. N Package 20-Lead Plastic DIP
1.040 (26.416) MAX 20 19 18 17 16 15 14 13 12 11
0.260 0.010 (6.604 0.254)
1 0.300 - 0.325 (7.620 - 8.255) 0.130 0.005 (3.302 0.127)
2
3
4
5
6
7
8
9
10
0.045 - 0.065 (1.143 - 1.651)
0.009 - 0.015 (0.229 - 0.381)
0.015 (0.381) MIN
0.065 (1.651) TYP 0.125 (3.175) MIN
(
+0.025 0.325 -0.015 8.255 +0.635 -0.381
)
0.065 0.015 (1.651 0.381) 0.100 0.010 (2.540 0.254)
0.018 0.003 (0.457 0.076)
N20 0592
S Package 20-Lead Plastic SOL
0.496 - 0.512 (12.598 - 13.005) (NOTE 2) 20 19 18 17 16 15 14 13 12 11
NOTE 1
0.394 - 0.419 (10.007 - 10.643)
1 0.291 - 0.299 (7.391 - 7.595) (NOTE 2) 0.010 - 0.029 x 45 (0.254 - 0.737)
2
3
4
5
6
7
8
9
10
0.005 (0.127) RAD MIN
0.093 - 0.104 (2.362 - 2.642)
0.037 - 0.045 (0.940 - 1.143)
0 - 8 TYP 0.050 (1.270) TYP 0.014 - 0.019 (0.356 - 0.482) TYP
0.009 - 0.013 (0.229 - 0.330)
NOTE 1 0.016 - 0.050 (0.406 - 1.270)
0.004 - 0.012 (0.102 - 0.305)
SOL20 0392
NOTE: 1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS. 2. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006 INCH (0.15mm).
12
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7487
(408) 432-1900 q FAX: (408) 434-0507 q TELEX: 499-3977
LT/GP 0494 10K * PRINTED IN USA
(c) LINEAR TECHNOLOGY CORPORATION 1994

▲Up To Search▲

Price & Availability of LT1161

	To Download LT1161 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .